Buffalo Nfiniti Wireless-N Router & Access Point
Page 1 of 1
"Draft N" wireless network gear such as the Nfiniti products from Buffalo Technology, which are available in stores today, offer a somewhat dubious value proposition. You get faster wireless networking and wider coverage now theoretically but run a risk that the equipment you buy will never comply with the final 802.11n standard and will never interoperate with other 11n equipment.
The 802.11n standard increases the theoretical maximum speed of a fully standards-based Wi-Fi network from 54 Mbps (under 11g and 11a) to 540 Mbps. It uses the 2.4 GHz band and is backward compatible with Wi-Fi 11g and 11b. To the existing standard, 11n most notably adds MIMO (multiple-input multiple-output) technology, which uses multiple transmitter and receiver antennas to increase data throughput and network range. One of the first things you'll notice about 11n routers is that they have three antennas rather than one or two.
But the IEEE (Institute of Electrical and Electronics Engineers), the standards body that developed the Wi-Fi standards, has yet to ratify a final version of 802.11n, and interoperability testing, a hugely important part of the process, has not begun.
The theory is that vendors will be able to upgrade Draft N gear to full compliance with the final standard later by simply updating device firmware. The risk part of the Draft N value proposition the possibility that it will turn out that vendors won't be able to upgrade these products to full compliance is difficult to gage at this point. The consensus seems to be that the risk is small, but there.
Buffalo, for example, is reportedly on record as saying it doesn't absolutely guarantee the Nfiniti products will be fully compliant. And you can bet that no vendor of Draft N equipment is offering to replace products if it turns out they can't be upgraded to full standards compliance. Linksys, Netgear, Belkin and others are also in this market.
What about the reward side of the proposition?
We recently had a chance to test the Buffalo Nfiniti Wireless Router & AP ($125 - $160) and Buffalo's Nfiniti Wireless Notebook Adapter ($80 - $120). The results were surprising, but consistent with what some other testers have found. The Draft N gear was not only not faster than standard 11g equipment, it was slower substantially slower in some of my tests.
To its credit, the Nfiniti router sets up easily. I simply unplugged my existing Linksys 11g router and all the devices connected to it by Ethernet cable, including a cable modem - and plugged in the Buffalo unit, in the same place on a shelf in my office. It automatically connected to the Internet within seconds.
Client devices with up-to-date 11g adapters had no trouble connecting to the Nfiniti router, but one desktop PC equipped with an older Actiontec 11b PCI card adapter could not initially connect it reported that it couldn't see any wireless networks within range, even though another PC in the same room had no trouble connecting to the Buffalo router. The 11b adapter later connected when I adjusted wireless settings using the Nfiniti router's configuration utility, though connectivity remained hit and miss.
The test procedure was simple. I copied a large (557 MB) file from my main PC, attached to the router via Ethernet cable, to a wirelessly connected laptop and timed the transfer using a stop watch. In the tests with the Linksys 11g router and a Buffalo 11g notebook adapter, it took 3 minutes and 47 seconds to copy the file when the notebook was in the same room as the router, 10 minutes and 41 seconds when the notebook was in a room 20 meters away where I typically get poor coverage.
It's worth noting here that to get the full benefit of an 11n wireless network, any wired connections to the network must be Gigabit Ethernet (1 Gbps). Fast Ethernet (100 Mbps) connections will be slower than the 11n wireless network. The desktop PC I used in the testing is equipped with a Gigabit Ethernet card so that was not a factor.
When I installed the Nfiniti router and notebook adapter, the Buffalo ClientManager reported that the link was "100%" when the notebook computer was in the same room as the router, and that the connection speed initially was 270 Mbps. However, it almost immediately downgraded the connection speed to 135 Mbps. Windows reported similar but slightly different speeds. All the reported speeds were still substantially faster than any 11g connection, though, so file transfer speeds should have been commensurately faster.
Nevertheless, when I did exactly the same test with the Nfiniti router and notebook adapter - using the same file, the same notebook, the same locations, it took longer to transfer the file: about 4 minutes and 40 seconds. I queried Buffalo's tech support group and was told there might be "wide-band interference." I was instructed to go into the configuration utility accessible with a Web browser and try changing transmission channels and the Control Sideband setting from "higher" to "lower."
I tried a few recommended configurations. None made any difference to the file transfer test results.
At this point, Buffalo decided it must be a hardware problem and shipped me a new set of Nfiniti equipment. While waiting for it to come, I performed the same tests again with the Linksys 11g router and Buffalo 11g notebook adapter and got exactly the same results. When the new Nfiniti equipment arrived and I repeated the test as described, the new unit was even slower.
These results were all the more curious given the other testing I did. One of the supposed benefits of 11n equipment is that it provides enough bandwidth in the wireless network to allow multiple simultaneous high-bit rate transmissions streaming video, for example. Some pay TV providers are considering Wi-Fi as a feasible medium for distributing video signals to various screens in a home.
I tested this with my existing 11g network by setting up streaming video transmissions between PCs over the wireless network using MPEG2-based video files. With one MPEG2 stream, video quality was good, with little noticeable latency. With two running, one of the streams was constantly interrupted. Video was no longer full motion but more like a slide show. With the Nfiniti Draft N gear in place, I was able to get two streams running, both with acceptable quality video.
Bottom line: The test results are at best ambiguous. Even if it turned out that both sets of equipment were faulty, it would be difficult, based on what I saw, to recommend the Nfiniti products. My recommendation is to wait for fully compliant 802.11n products.
Story courtesy of PracticallyNetworked.com.