DD-WRT Tutorial 5: Wireless Repeater
Page 1 of 3
In the old days, when you wanted to extend the range of a wireless access point, you had to set up a WDS, or wireless distribution system, coordinating two or more WDS-capable routers. But those days are gone and by those days, I mean 2006.
Setting up a WDS is a perfectly respectable thing to do. In fact, we earlier demonstrated precisely how to do it our second DD-WRT tutorial. But a WDS can be a needy thing. At a minimum, each router in the network must support WDS. For the most reliable results, each router should be the same model running the same firmware.
In the real world, you might own only one router which can run DD-WRT. Thanks to the new V24 beta firmware, a single DD-WRT router can be set up as a wireless repeater. Unlike a WDS, your DD-WRT router can now receive and redistribute a wireless signal from a generic AP.
Typically, you would use wireless repeater mode to rebroadcast a signal too weak for your wireless clients to pick up reliably assuming that your DD-WRT router can pick up the host AP, of course. In a test case, I successfully repeated a host AP with a signal strength of only 9% as seen by the DD-WRT router so low that the host AP wasnt detected at all by a laptop's integrated wireless.
Wireless repeater mode also groups your local clients into their own subnet a potential feature (for privacy) or a potential hassle (for LAN routing), depending on your needs.
Because wireless repeater mode is a new feature, and technically still in beta, using it puts you on the leading edge of DD-WRT technology. This also means you may run into problems with the limitations of wireless repeater mode, and there are some.
At the time of this writing, wireless repeater mode does not yet function in bridged mode. This means that, as noted earlier, clients connected to your DD-WRT repeater must be inside their own subnet, preventing them from seeing clients connected to the host AP.
For example, if your host AP assigns clients to the 192.168.0.x subnet, your wireless repeater will have to assign its clients to another non-overlapping private subnet, such as 10.0.0.x. While clients on both subnets will be able to access the Internet (assuming the host AP has Internet access), clients on the two subnets cannot see each other. For some LAN configurations this is an undesirable problem, and youll have to consider WDS or a wireless bridge scenario as alternate solutions, each with their own limitations.
To set up a wireless repeater yourself, youll first need to upgrade your DD-WRT compatible router to the latest V24 beta. If you are currently running a DD-WRT setup, take a moment to back up its settings before flashing to V24 (Administration/Backup), in case you later decide to revert to your original configuration.
Take note of any wireless security currently enabled on your host router. If you are using WEP, note your passphrase and key length (64-bit, 128-bit, etc.). If using WPA or WPA2, note your passphrase. Later, youll need to use these to set up your repeater. Note that because DD-WRT V24 is still a beta, your mileage may vary when it comes to repeating a secured host router. Users of earlier betas reported a number of problems, but these seem to be smoothed out with the latest releases (the V24 1/15/07 release, as I write this).
Also make note of the SSID of the host AP you want to repeat. Alternatively, you can scan for available APs from within the routers administration interface as well.
You will need to access the administration interface of the DD-WRT router youre setting up as the repeater. Connect a wired PC to the DD-WRT router. Be sure to disable any wireless adapter on your PC for now, and plug the Ethernet cable into one of the LAN (not WAN) ports on your DD-WRT router.
Step By Step
Assuming your DD-WRT is set to factory defaults, its IP address is 192.168.1.1. If your client PC is configured to receive an IP automatically, it should be assigned an address by the router.
Step 1. Open a browser on your PC and connect to the DD-WRT router its default address is http://192.168.1.1. The default login is root and password is admin. Of course, you should change these. If you dont, youll have bad dreams involving Sally Struthers and bathing.
Step 2. Click Setup/Basic Setup. You can leave Connection Type at its default, Automatic Configuration DHCP. You can leave the router and host name fields at default if you like, or customize them as we did.
The most important setting here is the Local IP Address. This must be a different subnet than that which the host AP is on. Our host AP is on 192.168.1.1, which was also the default for this DD-WRT router. Thus, weve changed the DD-WRT router to 10.0.0.1.
You can leave the remaining settings alone the DHCP enabled, etc. and click Save Settings at the bottom of the page. Your router will reboot.
Because it will restart with a new IP address, you will need to repair the client connection at your PC to join the new subnet. (Otherwise, you wont be able to access the administration page any more.)
In Windows XP, navigate to Control Panel/Network Connections, right-click on the Local Area Network connection, and choose Repair from the pop-up menu.
Once reconnected to the router, you should open your browser to its new address in this example, http://10.0.0.1.
Step 3. Click Security/Firewall and click to Disable the SPI Firewall. If you want any special firewall settings, you should configure these on the host router.
Step 4. Click Wireless/Basic Settings. For Wireless Mode change the selection from its default AP to Repeater.
Unless your host router is set to G-only mode, leave Wireless Network Mode set to Mixed. If your host router is set to G-only, likewise choose G-Only here.
Set the Wireless Network Name (SSID) to the SSID of your host router. If you dont know it and for some reason cant figure it out, well show you how to scan for it a little later.
Leave the remaining settings at their defaults. Some claim that setting Sensitivity Range (ACK Timing) to 0 improves performance, which you might experiment with once the repeater setup is tested and working.
Important: Now click Save Settings. The page will then refresh.