# OFDM: Old Technology for New Markets

For years, broadcast wireless networking was limited to practical speeds of
less than 11Mbps. Now, with the advent of Orthogonal Frequency Division Multiplexing
(OFDM)

It's not just WLANs; vendors like Flarion and NextNet Wireless are using OFDM to
bring similar increases to the metropolitan area network (MAN) over the much
more widely deployed Code Division Multiple Access (CDMA)

And, it's not just vendors; the IEEE 802.16a committee is working on a standard using OFDM for MANs as well.

While it's revolutionary to the wireless business, OFDM actually has a long history dating back to the late 1960s. As Navin Sabharwal, Director of Residential & Networking Technologies for Allied Business Intelligence, observes, "OFDM-based products span everything from wireless LAN to mobile access to digital television."

The principal driving force behind OFDM's increased popularity is the desire for faster wireless technologies and the increase in multimedia applications, which require higher speeds. In particular, In-Stat/MDR's Allen Nogee, Senior Analyst, Wireless Component Technology, thinks, "OFDM has much promise in the future, especially at the low-cost, high-capacity position."

It's not all-smooth sailing ahead for OFDM. While industry analysts think OFDM may succeed, it does have problems to overcome. Nogee, for example, comments that in cellular 4G, "Even if OFDM is proven to be superior technology, [the existing CDMA-based companies and carriers] aren't happy to share, and in cellular, it's more about politics sometimes than technology."

Worse -- despite the efforts of the OFDM Forum, technically, there are numerous incompatible OFDM standards.

### Inside OFDM

While OFDM has been around for more than 40 years, and has shown up in such
disparate places as asymmetric DSL (ADSL)

To understand why, we need to take a deeper look at how OFDM works.

Typically, OFDM, a spread-spectrum technology that gives wireless networking a new physical (PHY) layer, is implemented in embedded chipsets made up of radio transceivers, Fast Fourier Transform (FFT) processors, system input/output (I/O), serial to parallel and back again translators and OFDM logic.

In practice, the OFDM chipset bundles data over narrowband carriers transmitted
in parallel at different frequencies. High bandwidth is achieved by using these
"parallel subchannels (aka sub-carriers) that areas closely spaced as possible
in frequency without overlapping/interfering, according to Dr. Douglas Jones,
Professor of Electrical and Computer Engineering** **atUniversity
of Illinois at Urbana-Champaign. By being orthogonal, they have no overlap,
and thus do not interfere at all with each other. Orthogonal means that
they are perpendicular, but in a mathematical, rather than a spatial, sense."

This differs from the traditional analog modulation by transmitting a digital signal that's determined, Jones goes on to say, "by the use of the Fast Fourier Transform (FFT) algorithm. It can be better because it allows precise control of all those multiple simultaneous frequencies (carriers) used to simultaneously carry many data bits in parallel on different frequencies." With the use of the FFT on both transmitter and receiver, an OFDM system, "naturally and efficiently spaces the frequencies such that they are as close together as is possible and yet are orthogonal, so you get maximum bandwidth with no interference between subchannels."

In addition, to getting even better performance, OFDM deployments typically protect against intersymbol interference (ISI) by using a redundant symbol extension, the guard interval. Typically, ISI comes from multi-path delays. Jones explains that this is "the result of receiving not one, but several copies of the signal, due to multiple reflections (i.e., multipath), say, off buildings, airplanes, etc., of the transmitted signal. Since the reflections travel a longer distance to get to the receiver antenna, they are delayed, hence multipath delay spread." The simple guard interval performs error correction from multipath distortion without requiring complex error correction.

Jones explains, though, that by its very nature OFDM defeats multipath distortion,
a bane of single carrier methods like CDMA. OFDM combats it by transmitting
bits in parallel, with each bit being transmitted rather slowly. For example,
suppose I want to transmit 1,000,000 bits per second. I could transmit them
one at a time, each taking one microsecond to send. Any delay spread longer
than one microsecond would cause delayed reflections from multipath to overlap
the direct signal for the next bit, thus causing ISI. If instead I transmit
1000 bits in parallel at a time on 1000 separate OFDM subchannels, I can transmit
them 1000 times slower; that is, one millisecond to send them. A multipath delay
spread of 1 microsecond would only overlap 1/1000^{th} of the transmission
interval for any given bit, thus causing hardly any interference at all!

OFDM, though, has to contend with other problems besides multipath distortion. Two of the most important are frequency offset and phase noise.

These are, at heart, both engineering problems. Both can happen when the receiver's voltage-controlled oscillator (VCO) is not oscillating at exactly the same carrier frequency as the transmitter's VCO. When the problem is permanent, it's called frequency offset; when it varies over time, it's called phase noise jitter. In either case, it causes more errors because the no-longer orthogonal sub-carriers can interfere with each other.

The solution that IEEE 802.11a uses is to include a training sequence at the beginning of every packet using four of 802.11a's 52 subcarriers. These are then modulated with the known training data using binary phase-shift keying (BPSK) to produce "pilot tones." These tones let both sides determine the frequency offset and phase noise jitter between the transmitter and the receiver. Once known, adjusting the VCO's frequency and adaptively correcting for the current state of interference can deal with the interference.

Another problem with OFDM is that, like any multi-carrier system, it has vast variations between its peaks and valleys of signal power: the peak-to-average ratio (PAR). PAR's large dynamic range poses a real problem for power amplifier (PA) designs. There are many ways to deal with PAR and because of this OFDM implementations tend to use incompatible methods. On packet-based networks, like 802.11a, the approach is simply to limit power output and retransmit packets if data goes missing -- presumably because of a low powered transmission derived from a PAR incident.

This also results in another engineering problem that anyone who uses an 802.11a NIC in a laptop already knows about: OFDM cards eat power like a dad does Halloween candy after the kids are asleep. While there are efforts afoot to put OFDM on an electrical diet, any device using OFDM is going to consume more power than wireless devices that don't use OFDM for the PHY.

With these problems taken care of, a variety of different encoding methods can be used to transmit data over OFDM PHY. In 802.11a, these include BPSK for 6 to 9 Mbps, Quadrature Phase Shift Keying (QPSK) for 12 to 18Mbps, and Quadrature Amplitude Modulation (QAM) for speeds from 24 to 54Mbps.

*Next*: A look at New Uses for OFDM.